![]() ![]()
Reload the proFTPd service to pick-up the changes made in the configuration file: sudo service proftpd reload This is 60 seconds.Īnd uncomment DefaultRoot so users are ‘jailed’ to their home directories, they will still be able to access files on the USB HDD because of the ‘binded’ folder we created. Now edit the proFTPd configuration file: sudo nano /etc/proftpd/nfĬhange the TimeoutIdle value to 60. #Raspberry pi ftp server install#Install proFTPd: sudo apt install proftpd Now change the ownership of this folder to the ‘ftp-user’ user: sudo chown ftp-user:ftp-user /home/ftp-user/usb-hdd-storage Edit the ‘fstab’ file so this bind is permanent: sudo nano /etc/fstabĪdd this line to the bottom of the file, it should be below the line which was added in the previous step: /usb-hdd-storage /home/ftp-user/usb-hdd-storage none bind 0 0 Perform a bind to where the USB HDD is mounted. Note: If you need to unmount the drive, run: sudo umount /usb-hdd-storageĬreate a folder in the ‘ftp-user’ home directory, this will be used in the next step to ‘bind’ to the folder we created in /root/usb-hdd-storage: sudo mkdir /home/ftp-user/usb-hdd-storage To make the USB HDD mount permanently, edit the ‘fstab’ file: sudo nano /etc/fstabĪdd this line to the bottom of the file: /dev/sdaX /usb-hdd-storage ntfs defaults 0 0 You’ll also have to set permissions to ensure the drive can be accessed properly: sudo chmod 775 /usb-hdd-storage This can be found from the ‘blkid’ command. ![]() You may need to replace X with your drive ID. Now we know where our drive is, we need to mount it to the /usb-hdd-storage folder we created previously: sudo mount /dev/sdaX /usb-hdd-storage This should output the USB HDD’s label, keep a note of this.Ĭheck the boot name of the USB HDD’s partition: sudo fdisk -l Firstly check to see the partitions available on the USB HDD drive: sudo blkid Mount the USB HDD to this folder, this assumes your USB HDD is formatted as NTFS. This is where the USB HDD will be permanently mounted. The default Raspberry Pi pi user should be okay.Ĭreate a new user, used only for FTP connections: sudo adduser ftp-userĬreate a folder in /root. Login to SSH with root or a user which has sudo permissions. Note: FTP is not a secure protocol, I would recommend using SFTP for production environments. The instructions should work correctly in Debian and Raspbian too – in fact, you will probably have luck using these instructions on any Linux operating system, Raspberry Pi or not. Just as intended.For this setup, i’m using Ubuntu 16.04 running on a Raspberry Pi 3. cd (go to home directory)Īnd voila - it works from all browsers, and just takes a few minutes to install.Įverything else is working the same. Not going to work here, as most use Chrome. #Raspberry pi ftp server password#So I tried it, and it turns out to be complicated to get it installed, and once it was in my Firefox and Internet Explorer users could accomplish anonymous logins with minimal fuss, but Chrome insisted on prompting for a username and password every time. #Raspberry pi ftp server download#My question is: How can I set up an anonymous FTP server on port 21 so users on my private LAN can access daily summary files for download access without any login prompt or any other impediment to their access?įirst, I found in the Raspberry Pi documentation the recommendation to use pure-ftpd. #Raspberry pi ftp server windows#I have shut down and taken out the SD card and used Win32DiskImager to save an image of the system on my Win7 file server, then put the SD card back in and started up, and am running it as a headless system using Windows Remote Desktop in lieu of a dedicated HDMI display and keyboard. Zenmap on Windows shows the following ports: 22/tcp open ssh sudo apt-get install xrdpĪpache2 is installed and I can work on what it presents in /var/www That ' - ' in the name of the package is significant, you cannot omit it. ![]() (entered 8-character password, no password for view-only)Īlso installed xrdp for Windows Remote Desktop access. The first instruction in the resource you referenced is. I've installed tightvncserver for desktop access. I am using SSH and PuTTY for SSH terminal access FileZilla works well for sftp file transfers. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |